View 74VHC57404_6213406.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1/14 november 2004 high speed: f max = 180 mhz (typ.) at v cc = 5v low power dissipation: i cc = 4 a (max.) at t a =25c high noise immunity: v nih = v nil = 28% v cc (min.) power down protection on inputs symmetrical output impedance: |i oh | = i ol = 8 ma (min) balanced propagation delays: t plh ? t phl operating voltage range: v cc (opr) = 2v to 5.5v pin and function compatible with 74 series 574 improved latch-up immunity low noise: v olp = 0.9v (max.) description the 74vhc574 is an advanced high-speed cmos octal d-type flip flop with 3 state outputs non inverting fabricated with sub-micron silicon gate and double-layer metal wiring c 2 mos technology. these 8 bit d-type flip-flop is controlled by a clock input (ck) and an output enable input (oe ). on the positive transition of the clock, the q outputs will be set to the logic states that were setup at the d inputs. while the (oe ) input is low, the 8 outputs will be in a normal logic state (high or low logic level) and while high level the outputs will be in a high impedance state. the output control does not affect the internal operation of flip flop; that is, the old data can be retained or the new data can be entered even while the outputs are off. power down protection is provided on all inputs and 0 to 7v can be accepted on inputs with no regard to the supply voltage. this device can be used to interface 5v to 3v. all inputs and outputs are equipped with protection circuits against static discharge, giving them 2kv esd immunity and transient excess voltage. 74vhc574 octal d-type flip flop with 3 state outputs non inverting figure 1: pin connection and iec logic symbols table 1: order codes package t & r sop 74vhc574mtr tssop 74vhc574ttr tssop sop rev. 4
74vhc574 2/14 figure 2: input equivalent circuit table 2: pin description table 3: truth table x : don?t care z : high impedance figure 3: logic diagram this logic diagram has not be used to estimate propagation delays pin n symbol name and function 1oe 3-state output enable input (active low) 2, 3, 4, 5, 6, 7, 8, 9 d0 to d7 data inputs 12, 13, 14, 15, 16, 17, 18, 19 q0 to q7 3-state outputs 11 ck clock input (low-to-high edge triggered) 10 gnd ground (0v) 20 v cc positive supply voltage inputs output oe ck d q hxxz l x no change lll lhh
74vhc574 3/14 table 4: absolute maximum ratings absolute maximum ratings are those values beyond which damage to the device may occur. functional operation under these conditi ons is not implied table 5: recommended operating conditions 1) v in from 30% to 70% of v cc symbol parameter value unit v cc supply voltage -0.5 to +7.0 v v i dc input voltage -0.5 to +7.0 v v o dc output voltage -0.5 to v cc + 0.5 v i ik dc input diode current - 20 ma i ok dc output diode current 20 ma i o dc output current 25 ma i cc or i gnd dc v cc or ground current 75 ma t stg storage temperature -65 to +150 c t l lead temperature (10 sec) 300 c symbol parameter value unit v cc supply voltage 2 to 5.5 v v i input voltage 0 to 5.5 v v o output voltage 0 to v cc v t op operating temperature -55 to 125 c dt/dv input rise and fall time (note 1) (v cc = 3.3 0.3v) (v cc = 5.0 0.5v) 0 to 100 0 to 20 ns/v
74vhc574 4/14 table 6: dc specifications symbol parameter test condition value unit v cc (v) t a = 25c -40 to 85c -55 to 125c min. typ. max. min. max. min. max. v ih high level input voltage 2.0 1.5 1.5 1.5 v 3.0 to 5.5 0.7v cc 0.7v cc 0.7v cc v il low level input voltage 2.0 0.5 0.5 0.5 v 3.0 to 5.5 0.3v cc 0.3v cc 0.3v cc v oh high level output voltage 2.0 i o =-50 a 1.9 2.0 1.9 1.9 v 3.0 i o =-50 a 2.9 3.0 2.9 2.9 4.5 i o =-50 a 4.4 4.5 4.4 4.4 3.0 i o =-4 ma 2.58 2.48 2.4 4.5 i o =-8 ma 3.94 3.8 3.7 v ol low level output voltage 2.0 i o =50 a 0.0 0.1 0.1 0.1 v 3.0 i o =50 a 0.0 0.1 0.1 0.1 4.5 i o =50 a 0.0 0.1 0.1 0.1 3.0 i o =4 ma 0.36 0.44 0.55 4.5 i o =8 ma 0.36 0.44 0.55 i oz high impedance output leakage current 5.5 v i = v ih or v il v o = v cc or gnd 0.25 2.5 2.5 a i i input leakage current 0 to 5.5 v i = 5.5v or gnd 0.1 1 1 a i cc quiescent supply current 5.5 v i = v cc or gnd 44040 a
74vhc574 5/14 table 7: ac electrical characteristics (input t r = t f = 3ns) (*) voltage range is 3.3v 0.3v (**) voltage range is 5.0v 0.5v note 1: parameter guaranteed by design. t solh = |t plhm - t plhn |, t sohl = |t phlm - t phln | table 8: capacitive characteristics 1) c pd is defined as the value of the ic?s internal equivalent capacitance which is calculated from the operating current consumption without load. (refer to test circuit). average operating current can be obtained by the following equation. i cc(opr) = c pd x v cc x f in + i cc /8 (per flip-flop) symbol parameter test condition value unit v cc (v) c l (pf) t a = 25c -40 to 85c -55 to 125c min. typ. max. min. max. min. max. t plh t phl propagation delay time ch to q 3.3 (*) 15 8.5 13.2 1.0 15.5 1.0 15.5 ns 3.3 (*) 50 11.0 16.7 1.0 19.0 1.0 19.0 5.0 (**) 15 5.6 8.6 1.0 10.0 1.0 10.0 5.0 (**) 50 7.1 10.6 1.0 12.0 1.0 12.0 t pzl t pzh output enable time 3.3 (*) 15 8.2 12.8 1.0 15.0 1.0 15.0 ns 3.3 (*) 50 10.7 16.3 1.0 18.5 1.0 18.5 5.0 (**) 15 5.9 9.0 1.0 10.5 1.0 10.5 5.0 (**) 50 7.4 11.0 1.0 12.5 1.0 12.5 t plz t phz output disable time 3.3 (*) 50 11.0 15.0 1.0 17.0 1.0 17.0 ns 3.3 (*) 50 7.1 10.1 1.0 11.5 1.0 11.5 t w clock pulse width high or low 3.3 (*) 5.0 5.0 5.0 ns 5.0 (**) 5.0 5.0 5.0 t s setup time d to ck high or low 3.3 (*) 3.5 3.5 3.5 ns 5.0 (**) 3.5 3.5 3.5 t h hold time d to ck high or low 3.3 (*) 1.5 1.5 1.5 ns 5.0 (**) 1.5 1.5 1.5 f max maximum clock frequency 3.3 (*) 15 80 125 65 65 mhz 3.3 (*) 50 50 75 45 45 5.0 (**) 15 130 180 110 110 5.0 (**) 50 85 115 75 75 t oslh t oshl output to output skew time (note 1) 3.3 (*) 50 1.5 1.5 1.5 ns 5.0 (**) 50 1.0 1.0 1.0 symbol parameter test condition value unit t a = 25c -40 to 85c -55 to 125c min. typ. max. min. max. min. max. c in input capacitance 710 10 10pf c out output capacitance 9pf c pd power dissipation capacitance (note 1) 28 pf
74vhc574 6/14 table 9: dynamic switching characteristics 1) worst case package. 2) max number of outputs defined as (n). data inputs are driven 0v to 5.0v, (n-1) outputs switching and one output at gnd. 3) max number of data inputs (n) switching. (n-1) switching 0v to 5.0v. inputs under test switching: 5.0v to threshold (v ild ), 0v to threshold (v ihd ), f=1mhz. figure 4: test circuit c l =15/50pf or equivalent (includes jig and probe capacitance) r l = r1 = 1k ? or equivalent r t = z out of pulse generator (typically 50 ? ) symbol parameter test condition value unit v cc (v) t a = 25c -40 to 85c -55 to 125c min. typ. max. min. max. min. max. v olp dynamic low voltage quiet output (note 1, 2) 5.0 c l = 50 pf 0.6 0.9 v v olv -0.9 -0.6 v ihd dynamic high voltage input (note 1, 3) 5.0 3.5 v v ild dynamic low voltage input (note 1, 3) 5.0 1.5 v test switch t plh , t phl open t pzl , t plz v cc t pzh , t phz gnd
74vhc574 7/14 figure 5: waveform - propagation delays, setup and hold times (f=1mhz; 50% duty cycle) figure 6: waveform 2: output enable and disable times (f=1mhz; 50% duty cycle)
74vhc574 8/14 figure 7: waveform - pulse width (f=1mhz; 50% duty cycle)
74vhc574 9/14 dim. mm. inch min. typ max. min. typ. max. a 2.35 2.65 0.093 0.104 a1 0.1 0.30 0.004 0.012 b 0.33 0.51 0.013 0.020 c 0.23 0.32 0.009 0.013 d 12.60 13.00 0.496 0.512 e 7.4 7.6 0.291 0.299 e 1.27 0.050 h 10.00 10.65 0.394 0.419 h 0.25 0.75 0.010 0.030 l 0.4 1.27 0.016 0.050 k0 8 0 8 ddd 0.100 0.004 so-20 mechanical data 0016022d
74vhc574 10/14 dim. mm. inch min. typ max. min. typ. max. a 1.2 0.047 a1 0.05 0.15 0.002 0.004 0.006 a2 0.8 1 1.05 0.031 0.039 0.041 b 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0079 d 6.4 6.5 6.6 0.252 0.256 0.260 e 6.2 6.4 6.6 0.244 0.252 0.260 e1 4.3 4.4 4.48 0.169 0.173 0.176 e 0.65 bsc 0.0256 bsc k0? 8?0? 8? l 0.45 0.60 0.75 0.018 0.024 0.030 tssop20 mechanical data c e b a2 a e1 d 1 pin 1 identification a1 l k e 0087225c
74vhc574 11/14 dim. mm. inch min. typ max. min. typ. max. a 330 12.992 c 12.8 13.2 0.504 0.519 d 20.2 0.795 n 60 2.362 t 30.4 1.197 ao 10.8 11 0.425 0.433 bo 13.2 13.4 0.520 0.528 ko 3.1 3.3 0.122 0.130 po 3.9 4.1 0.153 0.161 p 11.9 12.1 0.468 0.476 tape & reel so-20 mechanical data
74vhc574 12/14 dim. mm. inch min. typ max. min. typ. max. a 330 12.992 c 12.8 13.2 0.504 0.519 d 20.2 0.795 n 60 2.362 t 22.4 0.882 ao 6.8 7 0.268 0.276 bo 6.9 7.1 0.272 0.280 ko 1.7 1.9 0.067 0.075 po 3.9 4.1 0.153 0.161 p 11.9 12.1 0.468 0.476 tape & reel tssop20 mechanical data
74vhc574 13/14 table 10: revision history date revision description of changes 12-nov-2004 4 order codes revision - pag. 1.
74vhc574 14/14 information furnished is believed to be accurate and reliable. however, stmicroelectronics assumes no responsibility for the co nsequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of stmicroelectronics. specifications mentioned in this publicati on are subject to change without notice. this publication supersedes and replaces all information previously supplied. stmicroelectronics prod ucts are not authorized for use as critical components in life support devices or systems without express written approval of stmicroelectro nics. the st logo is a registered trademark of stmicroelectronics all other names are the property of their respective owners ? 2004 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of 74VHC57404

	To Download 74VHC57404 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .